With the constant changes coming to the industrial and manufacturing sectors, and advanced equipment like laser marking systems becoming increasingly prevalent, it’s more important than ever to be aware of laser marking safety procedures.
These procedures range from ways to protect from bodily harm while utilizing laser marking systems to ways to avoid electrical dangers on the factory floor. It’s important to know what all of these dangers are and how to train yourself and your staff in essential laser safety.
Common Laser Hazards
One aspect to remember about laser marking safety is the variety of hazards associated with the systems which are also prevalent in many other forms of equipment. Basic safety training should mean workers are already familiar with some of these issues, but employers should be aware of:
- High voltage
- Compressed gasses
- Intense radio frequency energy
Let’s take a look at each of these individually:
- For concerns regarding high voltage, it’s important to know that pulsed CO2 lasers can produce internal voltages exceeding 25,000 volts while containing large capacitors that can deliver in excess of 200 Joules of energy.
- Some pulsed lasers also utilize a flowing gas design, which requires connection to a cylinder of compressed gas. Most of the gases used for laser systems are extremely safe, though since pressurized cylinders can pose a risk, their transportation and usage should occur only when the cylinders are properly restrained.
- As for radio frequency energy, severe burns can result from the improper servicing of units which use RF generators, such as sealed CO2 lasers. Anyone servicing such units should be trained in the unit’s safety procedures, and the connections for RF energy should not be touched during operation.
Due to the laser engraving safety checks in place for marking systems, units are designed in such a way to prevent operators from coming into direct contact with the laser beam.
One of the issues that can arise, however, involves unintentional reflected light, which falls into the following categories:
- Diffuse Reflections – This type of reflection occurs when a reflective surface’s irregularities create a scattering of light in all directions. Of the types of reflections, this is the safer of the two since energy is being divided in many directions and weakened.
- Specular Reflections – This type of reflection is produced in a way that is more mirror-like, recreating close to 100% of the original light compared to the scattered light of diffuse reflections. Though there is a higher danger associated with this form, it is much less common and laser marking systems are often designed to eliminate specular reflective surfaces that would come across the beam’s path.
With proper safety procedures in place, and by following guidelines which accompany your laser marking systems, these hazards should be greatly minimized.
Skin and Eye Hazards
Due to laser engraving safety checks in place, the effects of lasers on skin are usually considered of secondary importance. Compared to laser marking and engraving systems, high powered infrared lasers utilized in applications for welding and cutting pose a much greater risk of injury.
Some potential effects that can occur if safety procedures are not followed include mild reddening, blistering, and charring, all of which are usually reversible or repairable. Other potential issues could include ulceration, scarring of the skin, depigmentation and damage to underlying organs.
In regards to eye safety, some forms of laser beams operate at a wavelength which if exposed to the eye can pass beyond to the retina. With no pain indicators present and the beam being invisible, someone exposed can be unaware at the time of occurrence.
This is just another reason why utilizing industry-standard laser safety glasses is so vital to maintaining a safe and healthy workspace.
An additional hazard that can be posed when using laser systems is that of electrical shocks. Some of the ways shocks can occur is through contact with:
- Exposed utility power utilization
- Device controls
- Power supply conductors operating at potentials of 50+ volts
Operators and service workers for laser marking systems must be especially careful to avoid these dangers by following standard safety protocols. These hazards could be experienced during:
- Set-up and installation
- Maintenance and service
- Troubleshooting, if equipment protective covers are removed
The electrical injuries that can be sustained from improper and haphazard use of laser systems can include everything from a slight tingle to serious bodily injury to death. To avoid accidental contact with these energized conductors, laser marking units utilize a barrier system within the equipment.
In the United States, laser systems are overseen by the Center for Devices and Radiological Health (CDRH), which is a component of the FDA. Depending upon the risk of a specific type of laser, it is graded from Class I to Class IV. Laser marking lasers tend to be graded as Class IV lasers, making laser marking safety all the more important.
Two important additional classifications to keep in mind are the Maximum Permissible Exposure (MPE) and Nominal Hazard Zone (NHZ) designations.
- Maximum Permissible Exposure – This is the highest level of laser radiation an individual can be exposed to without receiving harmful physical effects to the eye or skin. Control measures for laser marking systems are in place to ensure any laser radiation emitted falls below the MPE.
- Nominal Hazard Zone – To create conditions for flexibility in laser marking applications, the laser beam of the unit is often not fully enclosed for practicality reasons. In these instances, it is necessary to define an area of potentially hazardous laser radiation, which is the NHZ. Control measures are then put into place for this area to ensure safety during use of the laser system.
Being fully aware of these classifications and their rationales are vital to ensuring proper workplace laser marking safety.
Learn More About Laser Engraving Safety Today
For a more detailed look at laser marking safety information, be sure to visit our laser safety manual, which includes graphics, information about warning labels, and procedural controls to utilize.
And if you have further questions for our team, or would like to know more about our premier line of laser marking systems, be sure to contact us today.
Counterfeit products remains a global phenomenon and continues to intensify over-time, making it a multi-billion-dollar market that can affect any product in any industry. The rapid trade of counterfeit products around the world poses a huge business threat for not only companies, but consumers as well. Counterfeit products are often of poor quality in addition […]
Laser marking and engraving has a wide variety of applications for businesses and hobbyists, with everything from the medical field to the everyday carry subculture and more getting real benefits from laser marked parts.
At TYKMA Electrox, we design and manufacture industrial laser marking machines for applications across an array of industries. When it comes to deep laser engraving, our systems serve as cost-effective solutions for your marking needs. From standard products to custom-made machines, our team strives to make sure that you are receiving the best product available. […]
Laser Marking in the Athletic Industry The market for the laser engraving industry has expanded significantly over the past few years. What used to be thought of as a process used only by industrial companies has broadened to reach businesses across many diverse fields. With countless applications and easy-to-use systems, laser marking has become a […]